rs4 bns engine built

[m2motortechnik]

At least you got rid of the boot spoiler... You did get rid of the boot spoiler didn't you?

naaaa

[pule333]

See Now we talking! Wasn’t difficult was it to start a meaning full thread full of pictures and sexy ass details . This looks epic! Wondering if magical 1000bhp is possible on this motor... keep it up.!


Sent from my iPhone using Tapatalk

[Bladerider]

Fair enough,

Dont want to come across as a nob on a thread thats actually of something interesting, but theres something very off about those times in a car with 850bhp, those are comparable to trap speeds of 650bhp GTRs (old RB engined ones) with similar weight, grip and dynamics.

Interested to see more as you post.
Im guessing Pauter rods ??

[Surrey Sam]

Nice seeing a built engine, you sticking with the wet sump?

[m2motortechnik]

Fair enough,

Dont want to come across as a nob on a thread thats actually of something interesting, but theres something very off about those times in a car with 850bhp, those are comparable to trap speeds of 650bhp GTRs (old RB engined ones) with similar weight, grip and dynamics.

Interested to see more as you post.
Im guessing Pauter rods ??

skylline gtr weight 3300 lbs at most compere to our 4000 lbs rs4 thats 700 lbs less ,and you are talking 650 whp not bhp ,my car makes about 700 awhp right now so its only a 50 whp diferance give or take
yes pauter custom made the rods to my specs and they are made in titanium

[m2motortechnik]

See Now we talking! Wasn’t difficult was it to start a meaning full thread full of pictures and sexy ass details . This looks epic! Wondering if magical 1000bhp is possible on this motor... keep it up.!


Sent from my iPhone using Tapatalk

my turbos are capable to flow enought for 1200 whp,everything is already done on my car,fueling ect....all i need is to swap the built motor in and start tuning it for for more boost
but i want to settle for 1000 whp give or take ,that my goal

[m2motortechnik]

Nice seeing a built engine, you sticking with the wet sump?

yes ,i already ran the stock engine till 9500 rpm a few times to check and loged my oil pressure and its all good

[Surrey Sam]

Nice seeing a built engine, you sticking with the wet sump?

yes ,i already ran the stock engine till 9500 rpm a few times to check and loged my oil pressure and its all good

Pressure should be fine, I'd have been tempted to Knife Edge the crank if sticking with the wet sump setup.

[m2motortechnik]

Nice seeing a built engine, you sticking with the wet sump?

yes ,i already ran the stock engine till 9500 rpm a few times to check and loged my oil pressure and its all good

Pressure should be fine, I'd have been tempted to Knife Edge the crank if sticking with the wet sump setup.

you dont need to there is baffle plate in thoes motor ,the crankshaft doesnt splash into oil,audi thought of everything on thoes motors

[Surrey Sam]

A little knifing would also balance out the reciprocal mass from installing your other lightweight components. Small gains, but still. It looks pretty.

[m2motortechnik]

A little knifing would also balance out the reciprocal mass from installing your other lightweight components. Small gains, but still. It looks pretty.

the crank assembly got fully balanced for the new weight of the rods and pistons

[dougle_turbo]

Please can we have some video? I want to hear it!

[dougle_turbo]

p.s great work

[Covkiller]

This is pornographic, keep it coming

[m2motortechnik]

Please can we have some video? I want to hear it!

not much videos but here is two,this is still on stock motor and 13 psi
https://www.youtube.com/watch?v=H62h5RiKOyk

https://www.youtube.com/watch?v=9ICemy_VU8w

this was a test pass at 11 psi and lower timing
https://www.youtube.com/watch?v=R1k9wt-o_hY