Charlie D's Build Thread

4.2 V8 32v Naturally Aspirated - 414 bhp
Post Reply
User avatar
CharlieD
2nd Gear
Posts: 160
Joined: Fri Sep 12, 2014 2:53 am

Re: Charlie D's Build Thread

Post by CharlieD » Wed Jul 01, 2015 12:46 am

I'm 95% sure it's the standard version Mike and yep, kept the stock resonator but with the milltek decats. No motorway drone but still savage when I put my foot down.

Absolutely love the decats and the raw sound they give... don't think I'll tire of the popping and crackling when decelerating either! Very happy with the setup so far, quiet when I want it to be, and goes mental when I choose :)

Here's a 9 second clip of me giving her a tickle when I got back home from MRC, this might help:
https://instagram.com/p/4kHzKxhXNQ/

Yeah the 350ps did strike me as being low... was hard to recall if the car had always been that slow or I'd simply got used to the power after the initial shock of buying it (I went from a bog standard 1.6 Golf to this) :)
RS4 B7 Phantom Black Saloon
[ MRC Stage 2 Map w/ LC/FS @ 440 PS ] : [ TubiStyle Exhaust ] : [ Milltek Decat Downpipes ] : [ Deflapped Manifold ] : [ Cold Air Feed ] : [ Revo/Pipercross CF Induction ] : [ H&R ARBs Front+Rear ]
[ Forged Rotor RS5.0 OEM+ 20x10.5 ] : [ AccuAir Airlift Performance + e-Level Mgmt ] : [ Wrapped in 3M Black Rose ]

Build Thread
Top
User avatar
RS04YOB
4th Gear
Posts: 906
Joined: Sun Jun 21, 2009 10:48 am

Re: Charlie D's Build Thread

Post by RS04YOB » Wed Jul 01, 2015 9:48 am

CharlieD wrote:Thanks Mike :) And yeah detango and trim Already on the radar... here's a photoshop of what she should look like soon :)

Image

Is the grill complete did you have you have make it yourself
Top
User avatar
CharlieD
2nd Gear
Posts: 160
Joined: Fri Sep 12, 2014 2:53 am

Re: Charlie D's Build Thread

Post by CharlieD » Wed Jul 01, 2015 11:58 am

Being fabbed up as we speak. Chopped out the mesh from a C6 RS6 grille and using the surround of a B7 A4 Sline grille. Trying to get it looking as OEM as possible and it's getting very fiddly. will get there in the end though :)
RS4 B7 Phantom Black Saloon
[ MRC Stage 2 Map w/ LC/FS @ 440 PS ] : [ TubiStyle Exhaust ] : [ Milltek Decat Downpipes ] : [ Deflapped Manifold ] : [ Cold Air Feed ] : [ Revo/Pipercross CF Induction ] : [ H&R ARBs Front+Rear ]
[ Forged Rotor RS5.0 OEM+ 20x10.5 ] : [ AccuAir Airlift Performance + e-Level Mgmt ] : [ Wrapped in 3M Black Rose ]

Build Thread
Top
User avatar
CharlieD
2nd Gear
Posts: 160
Joined: Fri Sep 12, 2014 2:53 am

Re: Charlie D's Build Thread

Post by CharlieD » Mon Jul 06, 2015 5:58 am

Just got back from GTI International @ Shakespeare Raceway, managed to pull 12.6s on the strip.

Fully air'd up the back to minimise squatting on launch and had the nose down, air con off of course (even though it was boiling hot in the car), traction control off...
Launch Control and Flat Shift worked a treat :mrgreen:

My brother was in the stand filming so will put a video up soon... though I think he missed the 12.6s run :boohoo:
RS4 B7 Phantom Black Saloon
[ MRC Stage 2 Map w/ LC/FS @ 440 PS ] : [ TubiStyle Exhaust ] : [ Milltek Decat Downpipes ] : [ Deflapped Manifold ] : [ Cold Air Feed ] : [ Revo/Pipercross CF Induction ] : [ H&R ARBs Front+Rear ]
[ Forged Rotor RS5.0 OEM+ 20x10.5 ] : [ AccuAir Airlift Performance + e-Level Mgmt ] : [ Wrapped in 3M Black Rose ]

Build Thread
Top
User avatar
Gavla
3rd Gear
Posts: 419
Joined: Tue Feb 28, 2012 11:28 am

Re: Charlie D's Build Thread

Post by Gavla » Mon Jul 06, 2015 1:11 pm

Yeah I was there also and saw you on the line with it's arse in the air - lol

It looked a bit odd going up the strip but hey if it worked ;-)

I managed 12.7 but was struggling to get the revs right on the launch. I'll check my vids as I think I might have captured one of your runs ;-)
RS4 (B7) Saloon Phantom Black, Black Optics, Tech Pack, KW Lowering Spring Kit, Stern Adjustable Arms, MRC Stage 2, Stage 1 Manifold, CAF, LOBA Stage 1 Clutch,
447ps/490nm (MRC), Scorpion Exhaust Non-Res Black Tips, Pre-cats gutted, Shadow Black Chrome Alloys, Viper Alarm, LED Interior lights, Tints
Top
User avatar
CharlieD
2nd Gear
Posts: 160
Joined: Fri Sep 12, 2014 2:53 am

Re: Charlie D's Build Thread

Post by CharlieD » Mon Jul 06, 2015 1:39 pm

If you did... you will be my new best friend :)
RS4 B7 Phantom Black Saloon
[ MRC Stage 2 Map w/ LC/FS @ 440 PS ] : [ TubiStyle Exhaust ] : [ Milltek Decat Downpipes ] : [ Deflapped Manifold ] : [ Cold Air Feed ] : [ Revo/Pipercross CF Induction ] : [ H&R ARBs Front+Rear ]
[ Forged Rotor RS5.0 OEM+ 20x10.5 ] : [ AccuAir Airlift Performance + e-Level Mgmt ] : [ Wrapped in 3M Black Rose ]

Build Thread
Top
User avatar
CharlieD
2nd Gear
Posts: 160
Joined: Fri Sep 12, 2014 2:53 am

Re: Charlie D's Build Thread

Post by CharlieD » Mon Jul 13, 2015 12:23 am

New show wheels :)

Image

Image

Image
RS4 B7 Phantom Black Saloon
[ MRC Stage 2 Map w/ LC/FS @ 440 PS ] : [ TubiStyle Exhaust ] : [ Milltek Decat Downpipes ] : [ Deflapped Manifold ] : [ Cold Air Feed ] : [ Revo/Pipercross CF Induction ] : [ H&R ARBs Front+Rear ]
[ Forged Rotor RS5.0 OEM+ 20x10.5 ] : [ AccuAir Airlift Performance + e-Level Mgmt ] : [ Wrapped in 3M Black Rose ]

Build Thread
Top
kernowrs4
1st Gear
Posts: 96
Joined: Sun Sep 15, 2013 9:49 am

Re: Charlie D's Build Thread

Post by kernowrs4 » Tue Jul 14, 2015 10:20 am

How did you get on with the grill ( if you have done the mod yet?)

Quite keen on trying this myself, any tips?
Top
User avatar
esp_mm-270
4th Gear
Posts: 624
Joined: Sat Dec 22, 2012 12:22 pm

Re: Charlie D's Build Thread

Post by esp_mm-270 » Tue Jul 14, 2015 12:51 pm

I did black "eye liner" when I did mine......
ImageUploadedByTapatalk1436874686.028335.jpg
ImageUploadedByTapatalk1436874686.028335.jpg (71.09 KiB) Viewed 4697 times
ImageImage
Image
Top
User avatar
CharlieD
2nd Gear
Posts: 160
Joined: Fri Sep 12, 2014 2:53 am

Re: Charlie D's Build Thread

Post by CharlieD » Fri Aug 07, 2015 3:04 am

So, she's looking quite sorry right now... that will change very soon however! (i.e. tomorrow :smile_smoking: )

Image
kernowrs4 wrote:How did you get on with the grill ( if you have done the mod yet?)

Quite keen on trying this myself, any tips?
I'd say take your time and do it slowly. Don't cut the bare mesh out of the RS6 grille, instead try to keep as much of the outer edge as possible and blend it in with the destination grille, using filler and such. It's still not done yet, attempting to get it as close to factory look as possible, will have a pic up when it's done, should be very soon! :)
esp_mm-270 wrote:I did black "eye liner" when I did mine......
ImageUploadedByTapatalk1436874686.028335.jpg
Very nice mate, funny you mention it... :lol:

Image
The photo doesn't do them justice tbh. Can't wait to get them fitted back on tomorrow along with the resprayed front bumper (stone chip delete 8) ):

Image

Image
RS4 B7 Phantom Black Saloon
[ MRC Stage 2 Map w/ LC/FS @ 440 PS ] : [ TubiStyle Exhaust ] : [ Milltek Decat Downpipes ] : [ Deflapped Manifold ] : [ Cold Air Feed ] : [ Revo/Pipercross CF Induction ] : [ H&R ARBs Front+Rear ]
[ Forged Rotor RS5.0 OEM+ 20x10.5 ] : [ AccuAir Airlift Performance + e-Level Mgmt ] : [ Wrapped in 3M Black Rose ]

Build Thread
Top
User avatar
Covkiller
Top Gear
Posts: 2349
Joined: Fri Mar 28, 2008 3:44 pm
Location: Coventry

Re: Charlie D's Build Thread

Post by Covkiller » Fri Aug 07, 2015 9:28 am

Why don't they do black or dark coloured undercoat. Dur :drink:
RS4 B7, Mugello Blue, K&W V3 & HR ARBs, set up by Centre Gravity, Milltek Valved Non Res & cat bypass pipes, BMC air filter, braided hoses, DOT 5.1, Terraclean, MRC Full Carbon Clean, MRC remap 448PS 477NM, 20" S7 alloys with 4mm spacers & Hawke spigots 66.6 > 57.1, AP Racing front discs. Sold Sept 2019. Now rocking an F80 M3
Top
User avatar
MikeFish
Cruising
Posts: 15588
Joined: Tue Aug 31, 2010 9:23 pm
Location: The Middle of Somewhere

Re: Charlie D's Build Thread

Post by MikeFish » Fri Aug 07, 2015 7:51 pm

Charlie, will you be displaying her at AITP this weekend?
Top
gt2
3rd Gear
Posts: 395
Joined: Fri Jun 28, 2013 11:28 pm

Re: Charlie D's Build Thread

Post by gt2 » Fri Aug 07, 2015 11:27 pm

Do you live anywhere near Lincolnshire? I've a tubi and am considering putting the stock centre section back in to get rid of the drone but I think it might lose a lot of the rawness of it. (Videos never sound as good as real life)
Top
User avatar
MikeFish
Cruising
Posts: 15588
Joined: Tue Aug 31, 2010 9:23 pm
Location: The Middle of Somewhere

Re: Charlie D's Build Thread

Post by MikeFish » Fri Aug 07, 2015 11:30 pm

gt2 wrote:Do you live anywhere near Lincolnshire? I've a tubi and am considering putting the stock centre section back in to get rid of the drone but I think it might lose a lot of the rawness of it. (Videos never sound as good as real life)
I had a Tubi with milltek non res centre section and it was ferocious. I changed the mid section for milltek resonated pipes and while still loud, the exact words I peevioulsy used ti describe it was that it had the rawness taken away, like it had lost its bite.
Top
gt2
3rd Gear
Posts: 395
Joined: Fri Jun 28, 2013 11:28 pm

Re: Charlie D's Build Thread

Post by gt2 » Fri Aug 07, 2015 11:32 pm

MikeFish wrote:
gt2 wrote:Do you live anywhere near Lincolnshire? I've a tubi and am considering putting the stock centre section back in to get rid of the drone but I think it might lose a lot of the rawness of it. (Videos never sound as good as real life)
I had a Tubi with milltek non res centre section and it was ferocious. I changed the mid section for milltek resonated pipes and while still loud, the exact words I peevioulsy used ti describe it was that it had the rawness taken away, like it had lost its bite.
That's a shame as it's the rawness of it that I like. It almost sounds like something's rattling the noise it makes but I love it.
Top
Post Reply

Return to “RS4 (B7 Typ 8E) 2006–2008”

Who is online

Users browsing this forum: Google [Bot] and 78 guests