Help with fault code - 01314 - Engine Control Module
- SimonS4MTM
- Top Gear
- Posts: 2314
- Joined: Thu May 29, 2003 2:40 pm
- Location: Norfolk
- Contact:
Help with fault code - 01314 - Engine Control Module
Hi all,
It's been a very long time since I have posted, but I am looking for some help.
My car has been sat away for quite some time, used for around 160 miles in the last 12 months. A few weeks ago I took it out for a spin and had engine cut out at high revs, over 6000 rpm. TC and EPC lights came on dash. Engine kept cutting out at high revs a few times when trying before i got home.
Found multiple fault codes with VAG-COM and cleared them.
Drove the car 1 week later and had the same engine cut issue at high revs. ABS fault code and ECM fault code logged with VAG-COM. Cleared the codes again.
Drove the car again today and engine cut again at high revs. ECM fault code logged again.
Fault code is;
1 Fault Found:
01314 - Engine Control Module
013 - Check DTC Memory - Intermittent
Freeze Frame:
Fault Status: 00101101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 40
Time Indication: 0
Freeze Frame:
Hex Value: 0x5C00
Hex Value: 0x4006
Hex Value: 0x0025
Hex Value: 0x01A3
Hex Value: 0x0001
This fault code has logged every time the engine has cut out.
I have searched the web and found a few suggestions. Anyone else have any experience of this and have anything to add.
Thanks in advance, cheeRS,
Simon
It's been a very long time since I have posted, but I am looking for some help.
My car has been sat away for quite some time, used for around 160 miles in the last 12 months. A few weeks ago I took it out for a spin and had engine cut out at high revs, over 6000 rpm. TC and EPC lights came on dash. Engine kept cutting out at high revs a few times when trying before i got home.
Found multiple fault codes with VAG-COM and cleared them.
Drove the car 1 week later and had the same engine cut issue at high revs. ABS fault code and ECM fault code logged with VAG-COM. Cleared the codes again.
Drove the car again today and engine cut again at high revs. ECM fault code logged again.
Fault code is;
1 Fault Found:
01314 - Engine Control Module
013 - Check DTC Memory - Intermittent
Freeze Frame:
Fault Status: 00101101
Fault Priority: 2
Fault Frequency: 1
Reset counter: 40
Time Indication: 0
Freeze Frame:
Hex Value: 0x5C00
Hex Value: 0x4006
Hex Value: 0x0025
Hex Value: 0x01A3
Hex Value: 0x0001
This fault code has logged every time the engine has cut out.
I have searched the web and found a few suggestions. Anyone else have any experience of this and have anything to add.
Thanks in advance, cheeRS,
Simon
| RS4 - B7 | Phantom Black | Seit 2017 |
| S4 - B5 | Ebony Black | Seit 2002 |
| S4 - B5 | Ebony Black | Seit 2002 |
Re: Help with fault code - 01314 - Engine Control Module
That seems very familiar to me..
I'd need to double check my logs, but the code rings a bell and the symptoms were the same.
Long story short, I needed two new ECUs...
Hopefully it's not the same for you.
Sent from my HD1903 using Tapatalk
I'd need to double check my logs, but the code rings a bell and the symptoms were the same.
Long story short, I needed two new ECUs...
Hopefully it's not the same for you.
Sent from my HD1903 using Tapatalk
Re: Help with fault code - 01314 - Engine Control Module
Oh crumbs.
I hope that’s not the case.
I have heard some people change relays for the ECU’s
Sent from my iPhone using Tapatalk
I hope that’s not the case.
I have heard some people change relays for the ECU’s
Sent from my iPhone using Tapatalk
Re: Help with fault code - 01314 - Engine Control Module
Yeah, that was the first course of action on mine but it did not solve it, so was new ECU time.
Now this was a main stealer and an independent might have had a different approach.
Sent from my HD1903 using Tapatalk
Now this was a main stealer and an independent might have had a different approach.
Sent from my HD1903 using Tapatalk
- SimonS4MTM
- Top Gear
- Posts: 2314
- Joined: Thu May 29, 2003 2:40 pm
- Location: Norfolk
- Contact:
Re: Help with fault code - 01314 - Engine Control Module
Anyone else got any advice. If not then I feel a trip to MRC might be needed.
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
| RS4 - B7 | Phantom Black | Seit 2017 |
| S4 - B5 | Ebony Black | Seit 2002 |
| S4 - B5 | Ebony Black | Seit 2002 |
Re: Help with fault code - 01314 - Engine Control Module
Maybe a bit of a long shot, but what about fitting a new MAF sensor? I've heard of it bringing on the TC lamp permanently when it goes faulty, and possibly with the car not getting used its not reading properly now....just a thought as an easy part to replace, and not too expensive compared to ECU's.
- SimonS4MTM
- Top Gear
- Posts: 2314
- Joined: Thu May 29, 2003 2:40 pm
- Location: Norfolk
- Contact:
Re: Help with fault code - 01314 - Engine Control Module
Cheers MIDZ.
The MAF was new just over two years ago just before a carbon clean at MRC.
Sent from my iPhone using Tapatalk
The MAF was new just over two years ago just before a carbon clean at MRC.
Sent from my iPhone using Tapatalk
| RS4 - B7 | Phantom Black | Seit 2017 |
| S4 - B5 | Ebony Black | Seit 2002 |
| S4 - B5 | Ebony Black | Seit 2002 |
Re: Help with fault code - 01314 - Engine Control Module
Ah ok Simon, that kind of rules that out then...strange it cuts out at 6K? maybe even try a vacuum function test with your VCDS and check everything works as it should
- SimonS4MTM
- Top Gear
- Posts: 2314
- Joined: Thu May 29, 2003 2:40 pm
- Location: Norfolk
- Contact:
Re: Help with fault code - 01314 - Engine Control Module
Anywhere between 6 and 8k.
Vacuum test is worth a go. Not done it before but I assume it straight forward with Vagcom?
Will take a look at the vac hoses for the exhaust valves that I blocked up a few years ago also.
Sent from my iPhone using Tapatalk
Vacuum test is worth a go. Not done it before but I assume it straight forward with Vagcom?
Will take a look at the vac hoses for the exhaust valves that I blocked up a few years ago also.
Sent from my iPhone using Tapatalk
| RS4 - B7 | Phantom Black | Seit 2017 |
| S4 - B5 | Ebony Black | Seit 2002 |
| S4 - B5 | Ebony Black | Seit 2002 |
Re: Help with fault code - 01314 - Engine Control Module
I've done it a couple of times and followed the good write up on here under the FAQ's thread. It's not a difficult test to run through
- SimonS4MTM
- Top Gear
- Posts: 2314
- Joined: Thu May 29, 2003 2:40 pm
- Location: Norfolk
- Contact:
Re: Help with fault code - 01314 - Engine Control Module

I will take a look
Sent from my iPhone using Tapatalk
| RS4 - B7 | Phantom Black | Seit 2017 |
| S4 - B5 | Ebony Black | Seit 2002 |
| S4 - B5 | Ebony Black | Seit 2002 |
Who is online
Users browsing this forum: No registered users and 128 guests