RS246.com Forum :: The World's #1 Audi R, S and RS Enthusiast Community

So over two or three threads you are aware that we are expecting some parts to be made in carbon fibre from Dubai, and thought it would be good if we had one thread on the subject.

I have personly sent some parts over so the parts can be made (I'm not a supplier or seller and am not making any money just so we are clear) at my own expense.

What I propose is for people to add their interest to what items they would like (obvious cost being a factor) by taking the whole list and adding your interest to each part on the list.

There may be more parts in the making so will add as we go along and hopefully will push the time line for different parts.

What I know is in the pipe line.

Rear diffuser: Doc,
Front Splitter: Doc,
Wing Mirrors: Doc,
Steering Wheel (Silver parts) exchange: Doc,
Carbon fibre intake kit: Doc,

Just cut and past the list from the last person so we can gauge the interest so that we get these parts made.

I am down for rear Diffuser. Maybe other bits depending on prices etc.

Also would be interested in Audi rings, especially the fronts if any at all in the pipe line

Rear diffuser: Doc, pule333,
Front Splitter: Doc, pule333,
Wing Mirrors: Doc,
Steering Wheel (Silver parts) exchange: Doc,
Carbon fibre intake kit: Doc,

Rear diffuser: Doc, pule333,
Front Splitter: Doc, pule333,
Wing Mirrors: Doc, eliano
Steering Wheel (Silver parts) exchange: Doc, eliano
Carbon fibre intake kit: Doc,

Mirrors and steering wheel (as you said cost dependant)

diffuser: Doc, pule333, Nickygrs4
Front Splitter: Doc, pule333, Nickygrs4
Wing Mirrors: Doc,
Steering Wheel (Silver parts) exchange: Doc,
Carbon fibre intake kit: Doc,

diffuser: Doc, pule333, Nickygrs4 rickster147
Front Splitter: Doc, pule333, Nickygrs4
Wing Mirrors: Doc, rickster147
Steering Wheel (Silver parts) exchange: Doc,
Carbon fibre intake kit: Doc

rickster147 wrote:diffuser: Doc, pule333, Nickygrs4 rickster147, Rw@@dy
Front Splitter: Doc, pule333, Nickygrs4
Wing Mirrors: Doc, rickster147
Steering Wheel (Silver parts) exchange: Doc,
Carbon fibre intake kit: Doc

Sent from my iPad using Tapatalk

What about looking into making replacement engine covers to swap out the old yellow ones?

Why would you try and engineer an intake kit when there is already a cheaper option from Pipercross?

rickster147 wrote:
diffuser: Doc, pule333, Nickygrs4 rickster147, Rw@@dy, lukes3
Front Splitter: Doc, pule333, Nickygrs4
Wing Mirrors: Doc, rickster147, lukes3
Steering Wheel (Silver parts) exchange: Doc,
Carbon fibre intake kit: Doc, lukes3

rickster147 wrote:
diffuser: Doc, pule333, Nickygrs4 rickster147, Rw@@dy, lukes3
Front Splitter: Doc, pule333, Nickygrs4
Wing Mirrors: Doc, rickster147, lukes3, eliano
Steering Wheel (Silver parts) exchange: Doc, eliano
Carbon fibre intake kit: Doc,lukes3

jonytek wrote:What about looking into making replacement engine covers to swap out the old yellow ones?

Why would you try and engineer an intake kit when there is already a cheaper option from Pipercross?

Like the idea of replacement engine covers, also what about the right hand side washer bottle cover

Rw@@dy wrote:

jonytek wrote:What about looking into making replacement engine covers to swap out the old yellow ones?

Why would you try and engineer an intake kit when there is already a cheaper option from Pipercross?

Like the idea of replacement engine covers, also what about the right hand side washer bottle cover


+1 to this ^^^^^

Rw@@dy wrote:

jonytek wrote:What about looking into making replacement engine covers to swap out the old yellow ones?

Why would you try and engineer an intake kit when there is already a cheaper option from Pipercross?

Like the idea of replacement engine covers, also what about the right hand side washer bottle cover

Pipercross didn't make it, site sponsors Revolution had the carbon air intake made and used a Pipercross air filter.
You can see the Revolution intake and the right hand side engine cover in the photo below:

[/URL]

I've got a spare right hand side engineer cover if required, the fixing has a broke and has been glued back together

When doing any engine covers at all if parts are being skinned the heat will be an issue.
I was the first to do them all and some seemed to hold out better than others I even did the scuttle panel

I would be interested in the side back trims of the front seats, and then the steering wheel silver parts a diffuser and possible front
splitter