Page 1 of 3

A2 bonnet vent dimensions?

Posted: Tue May 31, 2011 6:39 pm
by bam_bam
Does anyone have access to something that would tell the part number and dimentions for the bonnet vent on an A2?

Image

Re: A2 bonnet vent dimensions?

Posted: Tue May 31, 2011 8:35 pm
by drybeer
Ah.

I see what you need.

You actually need an A2 to measure / note part no.

Any on autotrader in your area?

Re: A2 bonnet vent dimensions?

Posted: Tue May 31, 2011 8:43 pm
by HYFR
good excuse to go for a drive Bam in the beast to hunt one down

Re: A2 bonnet vent dimensions?

Posted: Tue May 31, 2011 9:47 pm
by PJC
My neighbour has one if you want me to take a look.

Re: A2 bonnet vent dimensions?

Posted: Tue May 31, 2011 11:04 pm
by bam_bam
PaulRS4 wrote:My neighbour has one if you want me to take a look.
I'd really appreciate that! I see one on my cycle route to work and I've stopped twice to take photos but spotted some major curtain tweaking. I think whipping out a tape measure is a bridge too far. Some photos of the underside would be sweet too.

Re: A2 bonnet vent dimensions?

Posted: Tue May 31, 2011 11:08 pm
by PJC
Ok will do. pm your email address and I'll do it tomorrow.

Re: A2 bonnet vent dimensions?

Posted: Wed Jun 01, 2011 12:43 pm
by johnny11
we have a A2 and the missus will be back with it later today so if your stuck let me know.

Re: A2 bonnet vent dimensions?

Posted: Wed Jun 01, 2011 3:00 pm
by bam_bam
Cheers Jognny but Paul has come through with the good oil.
Thanks again mate.

Re: A2 bonnet vent dimensions?

Posted: Wed Jun 01, 2011 4:07 pm
by chunky79
Upgrade on the go?? You going to have 2 smaller vents each side of the bonnet?

dunc

Re: A2 bonnet vent dimensions?

Posted: Wed Jun 01, 2011 4:16 pm
by bam_bam
Not planning on it. I'll do the Sportec undertray mod plus have this A2 vent sitting neatly over the back of the engine (about 230mm back from the rear bonnet edge). I've also got the aux radiators to go on. Hopefully that'll keep everything cool and won't look too chavard. I'm thinking, most people won't even notice the A2 cooling vent mod.

Re: A2 bonnet vent dimensions?

Posted: Wed Jun 01, 2011 5:12 pm
by iR8V10
Will darth be the 1st or have you seen it somewhere else Luke?

Re: A2 bonnet vent dimensions?

Posted: Wed Jun 01, 2011 9:39 pm
by bam_bam
1st one I know of. It just dawned on me one day. Take a look at any bog standard med/large Merc from 2000-2004 and you'll see a similar vent. They're really innocuous but it's too long to fit on the '6. Then one day I noticed the little A2 had one. I've now measured it all up on the spare bonnet, I think it'll look very low key but still let a shitload of heat out. Looking forward to seeing it.

Re: A2 bonnet vent dimensions?

Posted: Thu Jun 02, 2011 6:53 am
by chunky79
Really good idea and should look smart. Have you tried a photo Shop pic at all? You of all people should be able to slap something together.

dunc

Re: A2 bonnet vent dimensions?

Posted: Thu Jun 02, 2011 9:02 am
by Shoppinit
What about water ingress?

Re: A2 bonnet vent dimensions?

Posted: Thu Jun 02, 2011 11:57 am
by bam_bam
Shoppinit wrote:What about water ingress?
It doesn't rain in London anymore.