Page 1 of 1

Sportec 19", and bent std 19"

Posted: Tue Feb 10, 2004 12:04 am
by Alan
Well I've finally got my 19" Sportec wheels fitted, and IMHO the car looks great [img]images/graemlins/nodder.gif[/img]

web page

However, the day before I collected them (thanks again Damian if you read this I hit the pothole also at the above link and wrecked two of the standard wheels [img]images/graemlins/033102bad_1_prv.gif[/img]
I couldn't avoid it, traffic coming the other way and as you can see this monster covered half of my side of the road!

And I was only doing 50-60mph, had the parents on board [img]images/graemlins/tung2.gif[/img]

Now there is no way I can blame the quality/strength of the wheel, but what I will rant about is the state of our roads [img]images/graemlins/jawdrop.gif[/img]

This was NOT a country back-route, it's an "A" road that is a very busy cut through from the M11 to the A1M [img]images/graemlins/director.gif[/img]

Re: Sportec 19", and bent std 19"

Posted: Tue Feb 10, 2004 12:48 am
by TarmacTerrorist
I'd be sending that photo of to the local council with a pic of the wheels and a bill, no way would I
let them get away with that.

Re: Sportec 19", and bent std 19"

Posted: Tue Feb 10, 2004 7:23 am
by Thorney
I'd be sending that photo of to the local council with a pic of the wheels and a bill, no way would I
let them get away with that.
Good luck, Suffolk CC are actually fighting me in court over the hump back bridge incident [img]images/graemlins/mad.gif[/img]

Re: Sportec 19", and bent std 19"

Posted: Tue Feb 10, 2004 10:23 am
by kcsun
I have done this twice with Essex Council and had the cheque within 1 month both times, you must send a picture and state exactly where and when it happened.

Simple

kc [img]images/graemlins/s4anogaro.gif[/img]

Re: Sportec 19", and bent std 19"

Posted: Tue Feb 10, 2004 10:56 am
by Alan
Sent off yesterday...that's why I took the picture [img]images/graemlins/grin.gif[/img]

Mind you good job I did, went back past it yesterday and it'd been filled!

Re: Sportec 19", and bent std 19"

Posted: Tue Feb 10, 2004 5:07 pm
by kcsun
That could be because someone else has also claimed against that hole [img]images/graemlins/033102scull_1_prv.gif[/img]

Good luck - let us know the outcome

kc [img]images/graemlins/s4anogaro.gif[/img]

Re: Sportec 19", and bent std 19"

Posted: Tue Feb 10, 2004 8:05 pm
by Gareth
Sent off yesterday...that's why I took the picture [img]images/graemlins/grin.gif[/img]

Mind you good job I did, went back past it yesterday and it'd been filled!


I did the same thing with Herts CC and got the full payment a little later. My BMW 18'' alloy badly damaged by a series of deep potholes near where I used to live.


Good luck! [img]images/graemlins/bigwave.gif[/img]

Re: Sportec 19", and bent std 19"

Posted: Tue Feb 10, 2004 8:07 pm
by Gareth
...oh if you need to buy some new (OEM) std 5 spoke RS6 alloys I have some for sale [img]images/graemlins/sekret.gif[/img]

cheers,
Gareth.