Question: Do the B7 19" 9J ET29 wheels fit onto a B5?

2.7 V6 30v biturbo - 380 bhp
JesseJonesJackson
Neutral
Posts: 22
Joined: Mon Aug 17, 2009 8:07 pm

Question: Do the B7 19" 9J ET29 wheels fit onto a B5?

Post by JesseJonesJackson » Sun Sep 26, 2010 8:37 am

I'm talking RS4's here

....if so can or should you run spacers?

...if so what width?

...is there anything else I should be aware of?

TVM...JJJ
RS4 B5 Black - MRC Custom Map, full Milltek system and downpipes, H&R ARB

User avatar
boxerdogted
3rd Gear
Posts: 457
Joined: Sat Mar 04, 2006 7:17 pm
Location: South Dorset

RE: Question: Do the B7 19" 9J ET29 wheels fit onto a B

Post by boxerdogted » Sun Sep 26, 2010 8:45 am

I'm running B7 RS4 wheels with 15mm Eibach Spacers and 275/30/19 Goodyear Asym tyres.
HTH
2001 RS4 Misano Red

jimbo1234567
5th Gear
Posts: 1411
Joined: Sun Jun 24, 2007 12:02 pm
Location: in the kitchen

RE: Question: Do the B7 19" 9J ET29 wheels fit onto a B

Post by jimbo1234567 » Sun Sep 26, 2010 10:19 am

you dont need spacers , they will fit fine without but its what you like the look of the best. an 8mm spacer will bring the et back to 20 from 28 but in my experience having the wheels stuck out just rashes the side of the car with stonechips. also remember that the b7 wheel is half an inch wider than a b5 one so with a 20mm et the wheel will already be 1/4 inch further out than a std wheel

User avatar
boxerdogted
3rd Gear
Posts: 457
Joined: Sat Mar 04, 2006 7:17 pm
Location: South Dorset

Re: RE: Question: Do the B7 19" 9J ET29 wheels fit onto

Post by boxerdogted » Sun Sep 26, 2010 11:19 am

jimbo1234567 wrote:you dont need spacers , they will fit fine without but its what you like the look of the best. an 8mm spacer will bring the et back to 20 from 28 but in my experience having the wheels stuck out just rashes the side of the car with stonechips. also remember that the b7 wheel is half an inch wider than a b5 one so with a 20mm et the wheel will already be 1/4 inch further out than a std wheel
It depends on what size tyres you use as to wether you need spacers, the fronts are not a problem but the rears are, 265/35/19 touch the rear suspension upright, 275/30/19 Goodyears clear by about 1mm which is to close in my opinion, you could just use an 8 or 10mm spacer on the rear.
As Jimbo said it depends what you like the look of.
2001 RS4 Misano Red

JesseJonesJackson
Neutral
Posts: 22
Joined: Mon Aug 17, 2009 8:07 pm

RE: Re: RE: Question: Do the B7 19" 9J ET29 wheels fit

Post by JesseJonesJackson » Sun Sep 26, 2010 3:29 pm

....So if I understand you correctly:

a 275/30/19 with an 8/10mm spacer will clear the suspension and miss the arch?

Whats the standard tyre size for the B7 RS4?
RS4 B5 Black - MRC Custom Map, full Milltek system and downpipes, H&R ARB

User avatar
boxerdogted
3rd Gear
Posts: 457
Joined: Sat Mar 04, 2006 7:17 pm
Location: South Dorset

RE: Re: RE: Question: Do the B7 19" 9J ET29 wheels fit

Post by boxerdogted » Sun Sep 26, 2010 5:05 pm

Std tyre size for B7 RS4 is 265/35/19.
They will clear the arch no problem as i run 15mm Hubcentric spacers and no rubbing.
275/30/19 Tyres are also cheaper than 265/30/19.
2001 RS4 Misano Red

User avatar
Virdee Autos
Trader (Expired)
Posts: 2546
Joined: Sun Jun 05, 2005 6:27 pm

RE: Re: RE: Question: Do the B7 19" 9J ET29 wheels fit

Post by Virdee Autos » Thu Sep 30, 2010 9:05 pm

255/35/19 is the standard tyre size used on the B7

You can usee anything from a 255/30 up to a 275/30/19 tyre on the B5.

With a 265 or 275 you will need to run spacers as the tyre fouls the rear suspension arm

If you use a 255/30, you don't need to run spacers, as the less width clears the suspension arm

Bear in mind not all tyre sizes are the same width, from make to make
Virdee Autos ~ 07950-526592

Noggy Blue RS4 - 710N's | Supersprint Exhaust | RS6 Calipers/RS4 Discs | Aero Wipers | B7 rear wiper | Pioneer AVIC-F10BT | Alcantara dash | Alcantara headlining | 15mm spacers | Pentagon Tints/Supaglass | After-run mod | Carbon steering wheel | R8 engine bay caps | Brushed Alu plate plinth |

jimbo1234567
5th Gear
Posts: 1411
Joined: Sun Jun 24, 2007 12:02 pm
Location: in the kitchen

RE: Re: RE: Question: Do the B7 19" 9J ET29 wheels fit

Post by jimbo1234567 » Fri Oct 01, 2010 1:06 pm

i have my 9.5 x 19 et 30 bimotos on with 275 30 assymetrics and no spacers, the wheels sit nicely in the arch and theres no rubbing front or back, these same wheels with 10mm spacers stuck out too much for me.

beastman
1st Gear
Posts: 71
Joined: Mon May 21, 2007 1:50 pm

Re: RE: Re: RE: Question: Do the B7 19" 9J ET29 wheels

Post by beastman » Fri Oct 01, 2010 4:23 pm

jimbo1234567 wrote:i have my 9.5 x 19 et 30 bimotos on with 275 30 assymetrics and no spacers, the wheels sit nicely in the arch and theres no rubbing front or back, these same wheels with 10mm spacers stuck out too much for me.
do you have standard suspension? I run these wheels with 10mm as felt suspension arm was too close so bought spacers. Guy I bought from had no spacers but ran coil overs.
Diesel, fuel of the devil!

RSTaSIS4
1st Gear
Posts: 52
Joined: Tue Jan 22, 2008 3:16 pm

RE: Re: RE: Re: RE: Question: Do the B7 19" 9J ET29 whe

Post by RSTaSIS4 » Wed Oct 06, 2010 3:11 am

I am currently running 18x10 all around with ET20 on coilovers, and do not have any issue with rubbing whatsoever.. Tires i am on 255/35/18..

kiwi_rs4
Neutral
Posts: 20
Joined: Thu May 29, 2008 8:11 pm
Location: Auckland, NZ

Post by kiwi_rs4 » Wed Oct 06, 2010 9:33 am

^^What wheels do you have?

RSTaSIS4
1st Gear
Posts: 52
Joined: Tue Jan 22, 2008 3:16 pm

Post by RSTaSIS4 » Wed Oct 06, 2010 9:40 am

kiwi_rs4 wrote:^^What wheels do you have?
I am Running on BBS LM

jimbo1234567
5th Gear
Posts: 1411
Joined: Sun Jun 24, 2007 12:02 pm
Location: in the kitchen

Re: RE: Re: RE: Question: Do the B7 19" 9J ET29 wheels

Post by jimbo1234567 » Thu Oct 07, 2010 10:30 am

beastman wrote:
jimbo1234567 wrote:i have my 9.5 x 19 et 30 bimotos on with 275 30 assymetrics and no spacers, the wheels sit nicely in the arch and theres no rubbing front or back, these same wheels with 10mm spacers stuck out too much for me.
do you have standard suspension? I run these wheels with 10mm as felt suspension arm was too close so bought spacers. Guy I bought from had no spacers but ran coil overs.
yes stock suspension, coilovers dont make any difference as its the cast iron arm that fouls the tyre, i modified mine to give another 3mm although the tyre didnt touch it was very close. the other alternative is to use 3mm spacers which will give you some more clearance but still allow the spigot to locate keeping the wheel centered.

JesseJonesJackson
Neutral
Posts: 22
Joined: Mon Aug 17, 2009 8:07 pm

Post by JesseJonesJackson » Sun Oct 10, 2010 9:36 am

Right...sounds like there are various configs that will work on the B5.

I could run the following tyres on the B7 wheels with the ET29 offset:

1) 255/35/19 with a 10mm spacers

2) 265/30/19 with a 10mm spacer

3) 255/30/19 without any spacers

4) 275/30/19 with a 10mm spacers


Correct?
RS4 B5 Black - MRC Custom Map, full Milltek system and downpipes, H&R ARB

Imola
Neutral
Posts: 1
Joined: Thu Mar 11, 2010 8:47 pm

Post by Imola » Tue Oct 26, 2010 10:03 pm

any pics of this combination (B7 wheels on a B5!)

Post Reply

Return to “RS4 (B5 Typ 8D) 1999-2001”

Who is online

Users browsing this forum: No registered users and 85 guests