rs4 front splitter

Post by **n4tbg** » Tue Aug 11, 2009 12:15 am

hi all,went to castle coomb a couple of weeks ago and seen a few rs4 and s4 with a lower splitter under the front bumper .any info on where to get them or any pics would be great .
thanks.

Post by **N11LS_J** » Tue Aug 11, 2009 3:41 am

Been done by a few people on here, do a search mate....

here's one thread I found

http://www.rs246.com/index.php?name=PNp ... t=splitter

Nils

Post by **quattrokid1** » Tue Aug 11, 2009 7:01 am

its a Seat Cupra R splitter cut to size.

Post by **Jules** » Tue Aug 11, 2009 8:12 am

Doesn't need cutting if fitted right

Post by **RS4KID** » Tue Aug 11, 2009 9:05 am

I searched on ETKA 1ML805903 but cannot find. Is this a correct part number?

Post by **Jules** » Tue Aug 11, 2009 9:58 am

Just go in to a seat dealer,they will know what you mean when you ask for a seat cupra r splitter
they sell loads of them,they laughed when i went in as i ordered 2 one for the rs4 and one for the golf.
He said people fit them to every thing,even rovers lol.
There about £17.00

Post by **Jules** » Tue Aug 11, 2009 10:25 am

Front splitter fitted to my rs4,girlfriends a3 and old golf

Post by **RS4KID** » Tue Aug 11, 2009 4:04 pm

The trouble is i am not in UK. Is there any website where I can buy it and get it shipped to Asia?

Post by **Virdee Autos** » Tue Aug 11, 2009 7:22 pm

Jules wrote:Doesn't need cutting if fitted right

Yep agree with that!

IF your totally stuck, drop me a PM, and I'll ship one out to you

Post by **rtd** » Tue Aug 11, 2009 8:51 pm

jules show us that pic of the splitter fitted to your sofa and microwave.........

Post by **Jules** » Tue Aug 11, 2009 8:52 pm

Bloomin hell rtd,have you been round my house

Post by **rtd** » Tue Aug 11, 2009 8:54 pm

Jules wrote:Bloomin hell rtd,have you been round my house

man you must have got a group discount!

Post by **quattrokid1** » Wed Aug 12, 2009 4:06 am

RS4KID wrote:The trouble is i am not in UK. Is there any website where I can buy it and get it shipped to Asia?

pm'ed you...

Post by **R5CPK** » Wed Aug 12, 2009 2:26 pm

Jules wrote:Doesn't need cutting if fitted right

Just ordered one of these today. Should be here Friday. Any hints/tips for fitting?? Is it best to screw or rivet it??? Any help gratefully received.

Thanks

Post by **quattrokid1** » Wed Aug 12, 2009 2:33 pm

you can see here on page 4 how mine was fitted

http://www.rs246.com/index.php?name=PNp ... t=splitter

drill holes in the lugs then hold it in place with sticky tape, then secure to the underside with self tapping screws, then trim at the edges of the wheel arch as shown on mine.

its far easier if you had a helping hand to keep it straight and still while you tape it up, check its semetricall and sits cosy to the bumper so you will have to shave the 2 middle sticky up bits until the edge of the splitter fits flush against the underside of the bumper.

THE 2 protuding bits in the centre need to be trimmed down about half an inch to allow the splitter to sit flush with the bumper... HOWEVER be carefull when securing near the centre section becuase there are hoses tucked up behind the lower bumper!!

Did your still cost 17 quid? I have asked Unit 20 to get me one so I can send it to the chap in Malaysia.

RS246.com Forum :: The World's #1 Audi R, S and RS Enthusiast Community

rs4 front splitter

rs4 front splitter

RE: rs4 front splitter

RE: rs4 front splitter

RE: rs4 front splitter

RE: rs4 front splitter

RE: rs4 front splitter

Re: RE: rs4 front splitter

RE: Re: RE: rs4 front splitter

Re: RE: rs4 front splitter

RE: Re: RE: rs4 front splitter

Who is online