RS246.com Forum :: The World's #1 Audi R, S and RS Enthusiast Community

anyone know of any good / trustworthy garages in west of scotland to get a re-map done off?
also what kind of cost should i be looking at?

cheers dave, no such problems for me yet DRC Failed 1 PatrickRS4 - Avant - 19,800 - Camberley - Dec 07 - NSF 2 RJKFlyer - Saloon - 11,500 - Sussex - Jan 08 - Fronts 3 MrM - Avant - 9,900 - Teesside - Feb 08 - Fronts & Valve 4 Marcus_RS4 - Saloon - 14,950 - Camberley - All 4 & Valves 5 mallinguard - ...

I had the same problem so Audi changed the following before replacing the clutch assembly under warranty Vacuum hose Master cylinder Slave cylinder The pedal would stick to the floor when you give it the beans, then go back to normal when you drove like an old man. thanks for all the responses. Mgb...

without sounding like a complete fu***ng <beep>, can someone pls explain what is going on?
i have no idea what problems u guys are having with DRC - pls feel free to fill me in

cheers

hi, recently i have found a problem with my clutch. when driving like a normal person - the clutch is absolutely fine. however when having a good go at my car and going into racing mode (even just for 10 - 15 seconds) the clutch becomes overly stiff and if i was to stop at a set of lights and then d...

That is looking the biz..... loving the full blown stealth look including the mirrors I wish I lived closer, as that for £250 seems a bargain, considering detailing prices I've seen Are the alloys a gloss or satin finish? alloys are a gloss finish as for living closer, give Dave a bell and he will ...

Stunning job, I wasn't aware that that kind of condition could be restored once you got swirls etc. yeh mate i wasnt aware either, but a good friend of mine had some work done on his type r not so long ago and when i saw that i was hooked on the idea!!! all i can say is that for 250 sheets u cant g...

thanks for all the comments guys

makes me feel a whole lot better

the good thing about the stealth look and the milltek is that my wife hates the car therefore refuses to be seen in it, which is great cos a can drive like a loony without the constant moaning!!!

alright guys, i had my car detailed last month, it was in some state after an accidnet i had. the bodyshop i used did a great job on the paint - but the buffing ruined that. rarher than a whole new paint job again - got a detailer out and what a difference!!! the guy i used is from KG detailing his ...

It’s unlikely it can affect performance though there is some evidence to suggest it can. If you look at my before torque curve in the 'MRC vs. Pippyrips B7 RS4' thread it dropped by about 20ftlb around 4,500/5,000 rpm when compared to Andyuk91and SR71's standard cars. My car was also standard at ...

what if he doesn't have the valved version? If it is the non-valved version... the vacuum tubes will be seen hanging freely above the mufflers. That is when they should be plugged, I used 1" long screws and have worked great! hi guys, i have the non valved system its in the garage just now and i wi...

hi mate , went in to see craig regarding the paint job ,guy seems to know what hes talking about but probably going to go for the vinyl wrap seems the better option have you got any pictures of your car he says its stunning? shindy, yeh craig is a good guy and knows his stuff did u see the van he h...

also just to add - i come across loads of the new m3's and always have a bit of fun (if the driver is up for it) and off the mark no m3 has ever got near me (no bullshit) however at the weekend i couldnt pull away from my mate who has an m3 this is where for me (if it wanst obvious already) that som...

hi, had a milltek fitted last week, car sounds great and what not but the performance is worrying. as all b7 rs4 drivers will know, when the foot is down u get a kick at around 4500rpm... since the exhaust has been fitted that kick is no longer there. i know my car inside out, had it 2 years done ju...

alright guys, i live in glasgow and am due to get my rs4 back later this week had a minor accident a few weeks back, the guy i have used is based in rutherglen, king street. he is insurance certified - went to see the car yesterday and av got to say he is doing a cracking job and his prices are no b...