Can any exhaust 'installer' install a Milltek

[RS6Mike]

Hi everyone,

My first post on here so apologies if it's a stupid question although that would keep me consistent.

I purchased a non-resonated Milltek cat back exhaust last month and I want to get it fitted. The nearest Milltek 'approved' centre is 70 miles from me which obvs makes a 140 round trip. Is this exhaust so specialised that the boys down Kwik fit couldn't install it? Just wondering whether any reputable exhaust installer can fit this with relative ease?

Many thanks

JUST TO ADD:
I haven't gone for a re-map, just an exhaust.

[jipettersen]

Cant see any problem with that. I had mine installed by a none-Milltek "exhaust garage" . A 120 minutes job.

[Fun and games]

It's not a hard job but i wouldnt trust kwik fit to even check my tyre pressures, find a decent local mechanic to do it for you

[Farravi]

I recommend Fourie Fabrication based in Banbury, Oxfordshire. He used to work for Doug @ MRC until recently when he decided to setup his exhaust business. He's doing jobs mainly on Audi's and gets alot of his business through MRC, so if they trust him then you know he's at the top of his game.


Sent from my iPhone using Tapatalk

[RS6Mike]

I recommend Fourie Fabrication based in Banbury, Oxfordshire. He used to work for Doug @ MRC until recently when he decided to setup his exhaust business. He's doing jobs mainly on Audi's and gets alot of his business through MRC, so if they trust him then you know he's at the top of his game.


Sent from my iPhone using Tapatalk

Thank for for the recommendation however I'm looking to get it done local hence my question.

[RS6Mike]

It's not a hard job but i wouldnt trust kwik fit to even check my tyre pressures, find a decent local mechanic to do it for you

Thanks

[RS6Mike]

Cant see any problem with that. I had mine installed by a none-Milltek "exhaust garage" . A 120 minutes job.

Cool, thanks for the feedback.

[MikeFish]

I recommend Fourie Fabrication based in Banbury, Oxfordshire. He used to work for Doug @ MRC until recently when he decided to setup his exhaust business. He's doing jobs mainly on Audi's and gets alot of his business through MRC, so if they trust him then you know he's at the top of his game.


Sent from my iPhone using Tapatalk

I wouldn't waste Stuarts time to fit a milltek. If you want an amazing custom exhaust then he is your guy but to fit a milltek go somewhere else.
And as stated I would avoid kwik fit too.

However, is this exhaust a cat back only system or full system with decat? If it's a full system then you will need a remap, if it's cat back only then anyone with a ramp and spanner can do it.

[Paulm]

Easy enough job. Did mine myself took about 3 hours. Just make sure they don't try the "oh we need to lower the subframe" one. No need to touch anything. One nut per side is tricky to get at but far from impossible

[RS6Mike]

I recommend Fourie Fabrication based in Banbury, Oxfordshire. He used to work for Doug @ MRC until recently when he decided to setup his exhaust business. He's doing jobs mainly on Audi's and gets alot of his business through MRC, so if they trust him then you know he's at the top of his game.


Sent from my iPhone using Tapatalk

I wouldn't waste Stuarts time to fit a milltek. If you want an amazing custom exhaust then he is your guy but to fit a milltek go somewhere else.
And as stated I would avoid kwik fit too.

However, is this exhaust a cat back only system or full system with decat? If it's a full system then you will need a remap, if it's cat back only then anyone with a ramp and spanner can do it.

Hi there. It's a cat back system.

[RS6Mike]

Easy enough job. Did mine myself took about 3 hours. Just make sure they don't try the "oh we need to lower the subframe" one. No need to touch anything. One nut per side is tricky to get at but far from impossible

Got quoted £170 by a 'reputable' exhaust/tyre centre. Tbh, if it's just bolting I'm fairly handy myself but one needs the right equipment to access the underside which I don't have. That being said, when it comes to the car, I'd rather the 'experts' do it than f*** it up myself.

[RS6Mike]

Easy enough job. Did mine myself took about 3 hours. Just make sure they don't try the "oh we need to lower the subframe" one. No need to touch anything. One nut per side is tricky to get at but far from impossible

Thanks but struggling with the 'easy enough' and '3 hours' in the same sentence!

[DragonRR]

Easy enough job. Did mine myself took about 3 hours. Just make sure they don't try the "oh we need to lower the subframe" one. No need to touch anything. One nut per side is tricky to get at but far from impossible

Thanks but struggling with the 'easy enough' and '3 hours' in the same sentence!

Fitted a Dash cam in my partner's F-Type last week. That was only 3hrs. Piece of piss.

[MikeFish]

Easy enough job. Did mine myself took about 3 hours. Just make sure they don't try the "oh we need to lower the subframe" one. No need to touch anything. One nut per side is tricky to get at but far from impossible

Got quoted £170 by a 'reputable' exhaust/tyre centre. Tbh, if it's just bolting I'm fairly handy myself but one needs the right equipment to access the underside which I don't have. That being said, when it comes to the car, I'd rather the 'experts' do it than f*** it up myself.

Surely that price is to supply and fit? Even then it's not that cheap.

[Paulm]

Easy enough job. Did mine myself took about 3 hours. Just make sure they don't try the "oh we need to lower the subframe" one. No need to touch anything. One nut per side is tricky to get at but far from impossible

Thanks but struggling with the 'easy enough' and '3 hours' in the same sentence!

What has time and degree of difficulty got to do with anything? Given its a big heavy exhaust routed to an exit on either side of the car and I am mega fussy how it fit things, also not trying to be a smart are that stating it's a 30 min job, I think my statement is fair and doable. Could I have done it in less time? Probably but then someone would have slated me for that as well.

Easy enough job, allow 3 hours but doable in 2 hours 38.5 minutes