RS246.com Forum :: The World's #1 Audi R, S and RS Enthusiast Community

Hi,

Selling my custom made 3 piece forged Adv.1 ADV08 Track Spec wheels. These have a stepped lip in Matt Black; 20" x 10" ET27; 5 x 112 PCD & CB of 66.56mm.

Will fit a variety of Audi S & RS vehicles but are made specifically for my RS4 B8. I'm lowered by approximately 20mm and the B8 easily accommodates 275/30 or 265/30 tyres without rubbing.

Also have spigot rings to reduce bore to 57.1mm if needed.

Bought new from Prestige Wheel Centre on 1st October 2014 at a cost of £6,750.00.

Wheels are in good condition with a few minor surface scratches; if they don't sell I will get them refurbished before remounting in Summer. Therefore, the cost of refurbishment is factored in to the asking price of Now Sold.

Would prefer thorough inspection of these rims by buyer before purchase (I'm based in Wigan); if that's not possible, these are boxed and can be shipped to anywhere in Great Britain at an additional cost of £100. Shipping to mainland USA is £500 (with insurance).

Thanks for looking

Dave

Lovely

Oooooh I'd be alllllllllllll over these had I still had the B7


#BARGAIN



GLWS David

N11LS_J wrote:Oooooh I'd be alllllllllllll over these had I still had the B7


#BARGAIN



GLWS David

Thanks Nils,

The following image is of the same wheel design (but with the more expensive Competition Spec spokes) and, by coincidence, the same specification at 20x10 ET27.

For more images see topic @

http://www.audizine.com/forum/showthrea ... ercharger)

Boxed up & ready to go

A couple of photos which demonstrates the mid-concavity of these alloys which is not always apparent from other images.

Thanks for looking.

I've seen this car a few times parked up and driving around and to be honest the pictures don't do the wheels justice. They look awesome.

P

moonigan wrote:I've seen this car a few times parked up and driving around and to be honest the pictures don't do the wheels justice. They look awesome.

P

Thanks moonigan; really appreciate your input.

I agree that the photos don't do them justice. Below is a YouTube video of a RS6 C7 fitted with same alloys but in titanium finish. I believe that these are 21" x 10" all round; fronts have a mid concave profile (same as mine) whilst rears have the deeper concave profile.



Thanks again.

Following some strong interest from members unable to view these in person, I have taken the following images of each wheel.

I reiterate that, IMHO, all four wheels deserve refurbishment and are priced accordingly. The spokes have very sharp edges and the blemishes have been caused by a jet wash set at too high a pressure (I foolishly allowed the Audi dealer to valet the RS4 following a service). There is no structural damage. I've tried to focus in on the worst offenders which are wheels 3 & 4 though wheel 1 does have some markings underneath the spoke where they 'float' above the outer rim.

Thanks again for looking.`

Wheel 1
Wheel 2
Wheel 3
Wheel 4

BMW2RS4 wrote: (I foolishly allowed the Audi dealer to valet the RS4 following a service).
Thanks again for looking.`

The Ultimate Sin !!

Bump

Do you have a price without the refurb?

Cheers!

NME wrote:Do you have a price without the refurb?

Cheers!

£2750; these would now cost over £8000 new.

£3250 with refurb in a gunmetal.

Aha, sorry misunderstood. Thought it included the refurb price. Decisions, decisions!

For a £7k set of wheels, the finish hasn't lasted too well has it? Surely they should withstand a bit of jet washing?