Paging All Milltek Heros!!!! advice needed

Post by **Daz** » Mon Jun 11, 2007 9:31 pm

Lee, was yours resonated or non-responated? I know of several people who've said that the non-resonated is just too intrusive and they've swapped it for the resonated one.

Post by **tartan_rob** » Tue Jun 12, 2007 10:48 am

Simon - I fitted it myself and the noise was not induction noise like sucking on 4pot. It was V8 roar. If it had of been induction noise it would have been taken straight out. The filter was oiled, but when I have fitted them before I have been able to see the oil, with this one I could not see anything and it did not feel as if there was oil on it.

Post by **SimonH** » Tue Jun 12, 2007 12:51 pm

Thanks Fellas for the replys,
Tartanrob, was asking about the oiled filter as regards to the oil affecting the airflow meter/MAF sensor, but im not sure if the RS4 uses this system without looking under the bonnet.Im not sure if its only turbo cars with this set up?.Regards, SIMON.

Post by **tartan_rob** » Wed Jun 13, 2007 12:53 am

time will tell if it starts to play up.

Post by **tartan_rob** » Wed Jun 13, 2007 12:56 am

time will tell if it starts to play up.

Post by **willr** » Thu Jun 21, 2007 10:41 pm

Anyone know what I should expect to pay for a Miltek resonated valved cat-back system, fitted?

Also, could anyone recommend a supplier/fitter in the South East - or should I go up to Ilkeston to get it fitted?

Post by **TDiAvant** » Thu Jun 21, 2007 10:44 pm

I would recommend going to Ilkeston to get your system fitted, they did a great job on my S4

Post by **ARSEY4** » Fri Jun 22, 2007 7:59 am

TDiAvant wrote:I would recommend going to Ilkeston to get your system fitted, they did a great job on my S4

What is the name of the retailer in Ilkeston please. Im not far from there.

Post by **willr** » Fri Jun 22, 2007 9:29 am

What is the name of the retailer in Ilkeston please. Im not far from there.

err.. Milltek

http://www.millteksport.com

Post by **djcevo** » Fri Jun 22, 2007 9:45 am

Tartan_Rob wrote:I got mine off fleabay. But is a genuine new replacement element from K&N. £35, job done. I can't describe the difference in noise from inside the car....even the wife said the noise was beautiful and my 64 year old dad (bless him) said "this sounds and goes like a race car".

http://cgi.ebay.co.uk/ws/eBayISAPI.dll? ... 0092443161

K&N part number # 33-2209

It also gives you opportunity to wedge open the air valve at front of airbox...

Rob, so the filter you are talking about is the same one as an S4 4.2 then?!?!?!? As there doesnt seem to be a different one or one at all for the RS4 4.2!?!?

Post by **ARSEY4** » Fri Jun 22, 2007 10:40 am

willr wrote:
What is the name of the retailer in Ilkeston please. Im not far from there.
err.. Milltek

http://www.millteksport.com

err.. Sport Tech actually

Thanks for the link.

Post by **willr** » Mon Jun 25, 2007 9:22 am

Had a look at the Sports Tech site. Looks like a good alternative.

I wasn't aware there was a stockist there, since Milltek claim to offer their own fitting service in Ilkeston too.

Anyone able to give me an indication of price? I'm still waiting to hear back from Milltek on this.

Cheers.

Post by **Love_iTT** » Mon Jun 25, 2007 9:24 am

willr wrote:Had a look at the Sports Tech site. Looks like a good alternative.

I wasn't aware there was a stockist there, since Milltek claim to offer their own fitting service in Ilkeston too.

Anyone able to give me an indication of price? I'm still waiting to hear back from Milltek on this.

Cheers.

I seem to remember that a valved, resonated cat back system was in the region of £1700 if thats any help.

Graham

RS246.com Forum :: The World's #1 Audi R, S and RS Enthusiast Community

Paging All Milltek Heros!!!! advice needed

Who is online