Milltek "Bulk Buy"

Post by **Stuart6587** » Wed Sep 30, 2009 6:10 pm

Discounts are off Miltek RRP and all suppliers seem to use this base so with a 25% discount I calculate this at £736.

Delivery is £15 inc VAT.

Unit 20 will fit FOC for Forum members.

I suspect from the feedback that I have had from most is that they want the exhaust delivered to them and will then presumably get their local tyre & exhaust centre to fit, as whilst Unit 20 will be close for some, for many it won't be (600 mile trip in my case !).

Now have seven interested, so just need a few more to hit the 25% discount:

1) Stuart6587
2) Rob8457
3) Spanner1210
4) Nudenut
5) JDS67
6) Alexrs6+
7) Hallans09

Post by **slimmyreed** » Wed Sep 30, 2009 6:15 pm

Daveperc wrote:
I am in oxford though, so driving to unit 20 isn't really practical for me...)
But driving to Banbury (MRC) is about 20 mins - and they do Miltek too!! So go get yourself the full stage 2 treatment and a grin from ear to ear!!

In fact - looking at your gearbox posting I see you are going there next week - all done in one trip sounds good to me!!

Dave

I fear the bill is going to be too much as it is...

Cambelt
oilcooler pipes
gearbox service
Secondary air injection

don't think i can add miltek to that list!

Post by **Daveperc** » Wed Sep 30, 2009 6:21 pm

Secondary air injection

Haven't come across that one - what's that??

Dave

Post by **slimmyreed** » Wed Sep 30, 2009 7:53 pm

its one of the 'common' faults on the RS6.

Is just emision related.

On a cold start the car injects fresh air into the exhaust manifold infront of the cats. This heats the cats up faster.

Mine isn't working, so my engine managment light is on. Rather than actually repairing it, the better solution is to remove it and re-program the car to stop looking for it (as it is prone to failure anyway). The plus side of this if i get it remaped, MRC will program it to stop looking for it at the same time. So I get my fault fixed and 500hp at the same time.

Post by **drybeer** » Wed Sep 30, 2009 9:24 pm

Well I'm pretty much deffo interested if we can get to 11 people through Grizz. I's a pain in the arse journey for me, but it's worth it I feel.

Post by **rob8457** » Wed Sep 30, 2009 9:31 pm

Dont want mine fitted as i will do it my self i understand its just bolt on any case should be simple.

Bobby

Post by **Cornishmoocher** » Wed Sep 30, 2009 9:33 pm

guys, fitting a cat back is really not that hard...... for those of you who dont want to drive to grizz try Woody, i trust him and he is dahn saaf. Tell him mooch sent ya.

GARTH ROAD MOT CENTRE LTD
Unit 2 1-7 Amenity Way Garth rd Morden Surrey SM4 4AX
Exhausts, Clutches, Diagnostics,Tyres, Servicing..

Post by **Cornishmoocher** » Wed Sep 30, 2009 9:36 pm

Actually, saying that Grizz knows Woody too... so... Not that I am trying to do grizz out f work, i love him and want have his babies, but for those of you who are too tight

to go and see him, it may be an option.

Post by **Stuart6587** » Wed Sep 30, 2009 10:20 pm

Now 8, so come on guys there must be 3 or more of you out there to make it to 11+ that want a Milltek............you know you want one !!!

1) Stuart6587
2) Rob8457
3) Spanner1210
4) Nudenut
5) JDS67
6) Alexrs6+
7) Hallans09

Drybeer

Post by **Cornishmoocher** » Wed Sep 30, 2009 10:23 pm

If i have one, that means I will have two- does that mean mine will be doubly loud?

Post by **philroach** » Wed Sep 30, 2009 10:31 pm

silly boy

Post by **SteveCuz** » Thu Oct 01, 2009 10:54 am

I am a maybe. Based in Northern Ireland but have been hoping to get the boat across and get loads of work done at the same time but have been so busy at work that I can't get my head around it.

The car is currently sitting in Audi to check the DRC. If that is gone I am going to try and see if my warranty will let me replace with coilovers and in that case I will plan a trip across and get it done right as well as full service and a complete health check.

At that point I might well be tempted to stick a zorst on!

Steve

Post by **raceman** » Thu Oct 01, 2009 3:21 pm

Hi All,
I would be very very interested. How much are we looking at? I know it's probably in this thread somewhere, just haven't got the time right now to go through the thread........lol

On a separate note, i need a complete re-brake discs pads etc all round, maybe use the + drilled discs. SAnyone any advice best place to get the parts from and roughly how much?

Cheers

Post by **Cornishmoocher** » Thu Oct 01, 2009 3:25 pm

Stuart6587 wrote:Discounts are off Miltek RRP and all suppliers seem to use this base so with a 25% discount I calculate this at £736.

Delivery is £15 inc VAT.

Unit 20 will fit FOC for Forum members.

I suspect from the feedback that I have had from most is that they want the exhaust delivered to them and will then presumably get their local tyre & exhaust centre to fit, as whilst Unit 20 will be close for some, for many it won't be (600 mile trip in my case !).

Now have seven interested, so just need a few more to hit the 25% discount:

1) Stuart6587
2) Rob8457
3) Spanner1210
4) Nudenut
5) JDS67
6) Alexrs6+
7) Hallans09

You didnt have to look far- it was at the top of this page!

Give Grizz a call..... I know, I know you are in kent and he is in Liverpool, but I used to do it from Paddock wood because it was still cheaper than going else where!

Post by **raceman** » Thu Oct 01, 2009 3:35 pm

dam, i'm going blind...............lol

You'll have to forgive me, it's my day off, hence not awake........l;ol

I'd be up for a milltek at that price, count me in.

I must have seen you in paddock moocher, i ran the Tesco Express till recently

RS246.com Forum :: The World's #1 Audi R, S and RS Enthusiast Community

Milltek "Bulk Buy"

Who is online